Heater Split Nuts with screws (Pair)

Split nuts for use on heater housings. Sold as a pair, with screws.

Inside diameter of the 2 inch heater split nut is approximately 3 inch.
Inside diameter of the 1. ... 
More

Heater Uni-Nut Kit with 3/4" Barbed Tailpiece, 3"

Replacement Heater Uni-Nut Kit with 3/4" Barbed Tailpiece. Typically used for 3" Low-Flo Heaters. ... 
More

Pump Unions with O-rings (Pair)

Pump Union Assemblies available in 1.0, 1.5, 2.0 and 2.5 inch. Sold as a pair, includes o-ring gaskets. ... 
More

Pump Union Split Nuts with screws (Pair)

Replacement pump unions split nuts. Sold as a pair. Not for use on heaters. Available in 1.5 inch, 2.0 inch and 2.5 inches.

MEASUREMENTS (approx):
The 1. ... 
More

Inline Bypass Kit

If your spa's plumbing is not ozone ready, you'll need this kit to inject the ozone. This system is the most effective means of getting ozone into your spa. ... 
More

EZ Install Plumbing Kit

Make installing your spa pack and spa controller as quick and simple as possible. ... 
More

Gate Valves (Pair)

It shocks us that some spas are built without gate valves, but some manufacturers skimp on this inexpensive, but helpful item. ... 
More

Pump Pot

Pump pots are needed when the spa pump is mounted near or above the water line. The pot prevents water from draining back into the spa when the motor is turned off. ... 
More

Pump Unions with O-Rings (Pair), 2.5"N x 2"S

Pump Union Assemblies with 2.5" female nut and 2" female slip tailpiece. Sold as a pair, includes o-ring gaskets.

A 2.5 inch pump union assembly has a 3.5 inch union nut. ... 
More

Elbow-90º with 5/16" Thermowell, 2" Slip x 2" Spigot

Elbow 90º with 5/16" Thermowell for dry sensor application. Will fit 5/16" sensors. This is a Street Elbow 90º with 2" Slip x 2" Spigot. Two rubber split gromments are provided. ... 
More

SpaGuts Plumbing Configuration, Right-To-Left, 2-Inch

Replacement SpaGuts Right-To-Left Plumbing Configuration. This plumbing configuration is specially assembled for SpaGuts brand Spa Pack that is configured for a Right-To-Left water flow. ... 
More

Pump Union Adapters with O-Rings, 1.5" FBT x 2.0" MBT (pair)

Pump Union Adapters with 1.5" female buttress (FBT) x 2.0" male buttress (MBT). Converts a pump thread fitting from 1.5" to 2.0".

Comes as a pair and include 1.5" o-rings. ... 
More

SpaGuts Plumbing Configuration, Left-To-Right, 2-Inch

Replacement SpaGuts Left-To-Right Spa Pack Plumbing Configuration. ... 
More

Shaft Seal Kit for Sta-Rite DJ Pumps, aka Cascades by Balboa

Replacement Shaft Seal Kit for Sta-Rite Brand Pumps or Cascades Pumps by Balboa. ... 
More

Elbow-90º with 5/16" Thermowell, 1.5" Slip x 1.5" Slip

Elbow 90º with 5/16" Thermowell for dry sensor application. Will fit 5/16" sensors. This is a Standard Elbow 90º with 1.5" Slip x 1.5" Slip. A rubber split gromment is included. ... 
More

Water Line Reducer, 2.0" Spg x 1.5" S (Pair)

A small number of spas have been built with mismatched plumbing. Usually the water intake and outlet sizes are the same, either 1.5 or 2 inches but in a small number of spas, one is 1. ... 
More